Maytag Epic Z Front Load Washer Problems
Maytag Epic Z Front Load Washer Problems.
Maytag Epic Z front-load washer error codes
These error code explanations can help you diagnose a problem with your Maytag Epic Z front-load washer.
When the control on your Maytag Epic Z detects a masalah, the washer stops and error code flashes on the control panel display. Follow the troubleshooting tips in the chart below to find the cause of the kebobrokan and fix your washer.
For repair how-to help, visit the PartsDirect repair help section, which includes repair help for washing machines, other major appliances, lawn and garden equipment, garage door openers, vacuum cleaners and more. Search for your transendental number to find a complete list of replacement parts for your washer.
Error Code
Condition
DIY advice
F01
Main control board EEPROM error
Check/Repair
The Electrically Erasable Programmable Read-Only Memory (EEPROM) on the main electronic control board is corrupted. Unplug the washer for 5 minutes, restore power and see if the code clears. If not, the replace the main electronic control board.
Possible parts
Main electronic control board
F03
Heating element broken
Check/Repair
The heating element has an internal short circuit. Unplug the washer and replace the heating element.
Possible parts
Heating element
F11
Motor control board failure
Check/Repair
Unplug the washer and check the wire harness connections between the induk bala control board and the main electronic control board. Reconnect any loose wires or replace the wire harness if damaged. If the wire connections are okay, replace the gembong control board.
How-to help
Possible parts
Gembong control board
F20
Not filling
Check/Repair
Make sure the water supply faucets behind the washer are fully open. Check the water fill lines for kinks or freezing in the winter. Check the water inlet valves. If the valves don’n open when activated, replace the water inlet valve assembly.
Possible parts
Water inlet valve assembly
F21
Will not drain
Check/Repair
The washer failed to drain within 8 minutes. Check the washer drain path for a clog or restriction. Clear the large item penapis in the drain pump. If the drain pump still doesn’t drain the water when activated, replace it.
How-to help
Possible parts
Drain pump
F22
Door lock failure
Check/Repair
Unplug the washer and check the wiring harness connections between the door lock assembly and the main control board. Reconnect any loose wires or replace the wire harness if damaged. If the wire connections are okay, replace the door lock assembly.
F23
Heating element failure
Check/Repair
Unplug the washer and check the wire harness connections between the heating element and the main control board. Reconnect any loose wires or replace the wire harness if damaged. If the wire connections are okay, measure the resistance with a multimeter. You should measure about 15 ohms of resistance through the heating element. Replace the heating element if you measure infinite resistance because that means the element is broken.
Possible parts
Heating element, wire harness
F24
Water temperature pengawasan error
Check/Repair
Unplug the washer and check the wire harness connections between the temperature sensor and the display control board. Reconnect any loose wires or replace the wire harness if damaged. If the wire connections are okay, replace the temperature sensor.
Possible parts
Temperature penapisan, wire harness
F25
Drive motor tachometer error
Check/Repair
Unplug the washer and check the wire harness connections between the motor control board and the drive motor. Check the wire harness connection between the motor control board and the main control board. Reconnect any loose wires or replace any damaged wire harness. If the wire connections are okay, replace the drive motor, which includes the tachometer as an internal component. If the problem continues, replace the motor control board.
How-to help
Possible parts
Drive motor, motor control board, wire harness
F26
Door switch error
Check/Repair
The control detects that the door hasn’n opened for 3 consecutive cycles or the door switch indicates the door is open with the door lock engaged. If you’ve run 3 consecutive cycles without opening the door, open and shut the door to clear the code. If the door switch detects the door open while locked, push on the door to make sure that it’s completely closed. Unplug the washer and check the wire harness connections between the door lock/switch assembly and the main electronic control board. Reconnect any loose wires or replace the wire harness if damaged. If the wire connections are okay, replace the door lock/switch assembly.
Possible parts
Door lock/switch assembly, wire harness
F27
Overflow
Check/Repair
The drain pump runs constantly in an effort to drain the water and the door stays locked. If the washer is overfilled, unplug the washer to see if water continues to fill the tub. Shut off the water supply and replace the water inlet valve assembly if the washer fills while unplugged. If the washer is empty when this code appears, unplug the washer and replace the water level pressure switch because it isn’cakrawala accurately detecting water level.
Possible parts
Water inlet valve assembly, water level pressure switch
F28
Communication error between the main electronic control board and the penggerak control board
Check/Repair
Unplug the washer and check the wire harness connections between the main electronic control board and the motor control board. Check the wire harness connections between the motor control board and the drive motor. Reconnect any loose wires or replace any wire harness that you find damaged. If those wire connections are okay, check the wire connections between the door lock/switch assembly and the main electronic control board. Reconnect any loose wires or replace the wire harness if damaged. A bad door lock/switch also prevents the motor control board from getting power, resulting in the F28 code. Replace the door lock/switch assembly if damaged. Replace the otak control board if the wire connections and door lock/switch assembly are both okay.
Possible parts
Motor control board, door lock/switch assembly, wire harness
F29
Door unlock error
Check/Repair
Unplug the washer. To manually unlock and open the door, remove the bottom front service panel, reach up into the cabinet and pull down on the manual release tab on the bottom of the door lock/switch assembly. Then pull the door open. Check for foreign objects in the door lock receiver. Clear any debris or objects from the receiver. If the door lock receiver is clear, check the wire harness connections between the door lock/switch assembly and the main electronic control board. Reconnect any loose wires or replace the wire harness if damaged. If the wire connections are okay, replace the door lock/switch assembly.
Possible parts
Door lock/switch assembly, wire harness
F30
Dispenser system failure
Check/Repair
Unplug the washer and remove the top washer panel. Check the wire harness connections between the dispenser actuator and the main electronic control board. Reconnect any loose wires or replace the wire harness if damaged. If the wire connections are okay, check the actuator cam and levers. Replace any damaged linkage components. If the cams and levers are okay, replace the dispenser actuator.
Possible parts
Dispenser actuator, dispenser actuator cam and levers, wire harness
F31 or F42
Pemrakarsa control board failure
Check/Repair
Unplug the washer and check the wire harness connections between the biang kerok control board and the drive otak. Reconnect any loose wires or replace the wire harness if damaged. If the wire harness connections are okay, replace the motor control board.
How-to help
Possible parts
Dalang control board, wire harness
F32 or F35
Water level sensor failure
Check/Repair
Unplug the washer and check the wire harness connections between the main electronic control board and the water level pemeriksaan. Reconnect any loose wires or replace the wire harness if damaged. If the wire harness connections are okay, replace the water level sensor.
Possible parts
Water level sensor, wire harness
F70 or F71
No communication between the main electronic control board and the user interface control
Check/Repair
Unplug the washer and check the wire harness connections between the main electronic control board and the user interface control. Reconnect any loose wires or replace the wire harness if damaged. If the wire connections are okay and the leger rotates before the code appears, replace the user interface control. Replace the main electronic control board if the lembah doesn’t rotate before the code appears.
Possible parts
Main electronic control board, user interface control, wire harness
rL or F34
Load inside the washer during the Clean Washer cycle
Check/Repair
You can only run the Clean Washer cycle with the tub empty. Remove any clothes from the washer and restart the Clean Washer cycle. If you had no clothes in the washer when starting the Clean Washer cycle, then you’ll likely need to replace the spin bearing because the bearing isn’lengkung langit allowing the spin bola keranjang to rotate smoothly. The spin bearing is a component of the outer tub and isn’cakrawala available as a separate part. Replace the outer tub if the spin bearing failed.
Sd
Excessive suds
Check/Repair
Excessive suds is detected during the cycle. The cycle goes into a suds kill routine by filling the tub with water and then tumbling the clothes. If this routine doesn’cakrawala eliminate the suds, the control displays the Sd code. Use the right amount of high-efficiency (HE) detergent with future loads.
Possible parts
HE detergent
F99
User interface control or main electronic control board failure
Check/Repair
Unplug the washer and replace the user interface control. If the problem continues, replace the main electronic control board.
Possible parts
User interface control, main electronic control board
Symptoms common to all washers
Choose a symptom to see related washer repairs.
Articles and videos common to all washers
Use the advice and uang pelicin in these articles and videos to get the most out of your washer.
Maytag Epic Z Front Load Washer Problems
Source: https://www.searspartsdirect.com/diy/error-codes/washer-repair/1234598/maytag-epic-z-front-load-washer/3048