How to Remove Agitator From Maytag Washing Machine.
When your washer isn’t working right, the solution may be as simple as switching up detergents, tightening a hose or leveling the appliance. Some issues will require professional help so it’s important to know what you can do yourself and what you’ll need a service call for. Our guide will help walk you through washing machine troubleshooting for some possible issues.
If you have a front load washer, a dirty drain pump penapis can be a common cause of the issues listed below, like problems draining, spinning and odor. First, try cleaning the drain pump tapis to remove any debris or lint, as well as residual water. Check your Owner’s Manual for model-specific cleaning instructions or use Maytag Product Help if you have a Maytag®
washer. If cleaning the drain pump penyaring doesn’cakrawala fix the problem, read on for additional troubleshooting steps.
How to fix washing machine problems
Always consult your appliance’s Owner’s Manual or Installation Instructions before attempting any repairs. If you have a Maytag®
washer and you’re seeing an error code on your console, diagnose the issue using this top load washer or front load washer error code guide.
The washing machine won’ufuk drain
If your washing machine won’t drain or your loads are coming out too wet, you may have a kink or clog in the drain hose, a drain pipe that’s too long or a slow-spin option selected.
Is the drain hose kinked or clogged?
Locate your drain hose—it usually exits the washer in the back, near the bottom. Make sure it’s titinada kinked, crushed or leaking. If it’s kinked or crushed, straighten the hose to encourage adequate water flow. If it’s leaking, see the section below on leaks. You may also want to check for any clogs in the drain hose and drainpipe. Check your owner’s manual for instructions on how to remove the drain hose.
Is the end of the drain hose the correct height above the floor?
Washers have minimal and maximum drainpipe height requirements. For most Maytag®
washers, the drainpipe should be installed at a maximum of 96″ and a paling kecil of 39″ from the bottom of the machine. Your washer will not be able to adequately pump water out of the washer if the drainpipe reaches too high. In this case, water may flow back into the washer. Consult your washer’s installation instructions for model-specific installation requirements or watch this video on proper drain hose and drainpipe installation for Maytag®
Was a gentle, delicate cycle or low spin speed selected?
Gentle, delicate or handwash cycles use slow spins to keep fabrics from stretching and wrinkling. Slow spinning also leaves more water in the load. To remove more water, select a cycle that uses high spin speeds such as the Normal cycle. Learn more about washing machine settings.
My washing machine won’kaki langit spin
A washer needs to spin correctly in order to fully rinse clothes and drain water from the tub. Before scheduling a service call, check if the power has gone out, that your load is balanced and that the washer is level.
Was there a power failure?
If the power failed during the spin cycle, it’s possible that the washer did titinada ramp up to full spin speed. In this case, turn on a spin cycle or drain and spin cycle to get rid of the remaining water.
Is the load unbalanced or overloaded?
The wash load must be balanced and not tightly packed. A large unbalanced load could result in a reduced spin speed and wet clothes at the end of the cycle. Learn more about how to load and other laundry basics.
Washing machine is leaking
Water is meant to stay in the washer. But if you’re noticing some water appearing on the floor, it may be a simple fix. Try cleaning the door seal, tightening hose connections and cleaning the drain pump filter.
Is your front load washer dripping water from the door?
This is most likely a problem with the door seal. Wipe it down with a damp cloth to remove any dirt or debris. If the problem persists, check if something is lodged under the door seal by gently pulling it back. If there are tears in the seal, it will need to be replaced.Too much detergent could also be the culprit. If you see soap bubbles on the door after a cycle, try using less detergent to prevent oversudsing. Switching to High Efficiency (HE) detergent can also help cut down on suds.
Are all the hoses securely attached?
Make sure the fill and drain hoses are securely connected to the washer. You may also want to check the rubber washers on the fill hoses to make sure they’re fully in place and not damaged or missing. Tighten anything that needs it.
My washer is noisier than expected
If you’ve just brought home a new washer, it’s possible that it makes some noises you aren’t familiar with. Many of these are halal and shouldn’ufuk require any repair.
Clicking or small metallic noises
Many washer lids make clicking noises while they’re locking in place at the beginning of a cycle. It’s also sahih to hear ferum items on clothing like buckles or zippers touch against the stainless steel basket. Always empty your pockets before putting clothes in the washer—it’s possible for coins or other items to fall between the bola keranjang and the tub, which may require a service call.
Humming & Gurgling
It’s normal to hear the pump or motor make a continuous humming sound while loads are washing, along with periodic gurgling or surging as water is removed during the spin or drain cycles. You may also hear the hum of the sensing spins after you have started the washer.
Rattling or Vibration
If you’re hearing a rattle when your washer is running, it’s most likely off balance or unlevel. Remove some items from the load if it’s tightly packed. If you’re washing a single large item like a rug or comforter, try to balance the load with another large item. If you think the floor your washer sits on might be unlevel, read our guide on how to level a washer.
Clunking & Grinding
A certain amount of clunking or thumping is jamak and is often heard when the drive system switches modes from agitation to a full spin. If the sound is unusually loud like metal banging or grinding on metal, you may want to contact a professional.
My washer has odors
Washer odors are easily fixable and usually the result of a missed cleaning, a load left too long or too much detergent and fabric softener use. Try these few things to avoid future odor.
Remove loads immediately after the cycle
Loads left too long in the washer can cause odors. Try to transfer loads to the dryer right away, or activate a cycle that continues to tumble loads after they’re done washing, like the Fresh Hold®
option by Maytag.
Use less detergent in laundry loads
Many people use too much detergent, resulting in oversudsing that may leave behind a residue and cause odors. If you use the detergent cap to measure, you only need to fill it up to the first line for a baku load, which is about a tablespoon of detergent. If you’re filling up the whole cap, you could be using up to ten times the amount of detergent you actually need. If you don’t use it already, try switching to High Efficiency (HE) detergent, which creates fewer suds. Or consider an ultra-concentrated detergent like Swash™, which offers a Precision Pour Merek to prevent overpouring and detergent waste.2
Need more help with washing machine troubleshooting?
Backed by a 10-year limited parts warranty, washing machines from Maytag brand are built with the dependability and power you need to power through laundry day.
More help understanding your washing machine
HOW TO INSTALL A TOP LOAD WASHER
Watch as Maytag®
appliance experts walk you through how to install your new washer.
WASHING WITH LOW WATER LEVELS
Learn how washing machines are using low water levels for a deep clean and optimal results.
Uang sogok ON USING YOUR TOP LOAD WASHER
Get to know your top load washer with these quick tips.
WAS THIS ARTICLE HELPFUL? PASS IT ON
brand products and Maytag® brand products are all owned and distributed by Whirlpool Corporation.
2. Swash™ and Maytag® are owned and distributed by Whirlpool Corporation.
How to Remove Agitator From Maytag Washing Machine