Kenmore Washer Pumps

Popular Kenmore Washer Pumps

Washing Machine Drain Pump and Gembong Assembly

PartSelect Number
PS3579318

Manufacturer Part Number
4681EA2001T

The drain pump and dalang assembly may also be known as the washer drain pump and is a part for your washer. The drain pump helps expel water from the washing machine. The drain pump is activated after the spin cycle speed is maintained for a specific period of time. To make this installation you will need a Phillips screwdriver, a small flat-blade screwdriver, a pair of needle-nose pliers, and a pair of slip-joint pliers. Note that the pump casing is not included. This medium-difficulty repair may vary, but can generally be started by disconnecting power, then removing the top of the washer by taking out the four back screws and two small brackets. Then, remove the front panel by taking out the two screws and eight tabs that should be taken from the top. Moving down the front of the washer, remove the door, latch, tub gasket, and drain cover. Disconnect the drain hoses and clip from under the drain assembly, and install new assembly from there. Reassemble parts in direct reverse bestelan — taking photos during disassembly and keeping parts clearly organized can help here. Despite the number of steps, you will only need a standard Phillips screwdriver to complete this repair.

Fixes these symptoms

  • Engine runs but does not pump water
  • Leaking
  • Noisy
  • See more…

Installation Instructions

Jorge from Apple Valley, CA

Washing maching wouldn’falak drain

Removed the top of the washer by removing the 4 back screws and 2 small brackets. Then I removed the front panel, this was actually the hardest part, 2 screws and 8 tabs that you pop out carefully from the top of the panel. I only disconnected the power button and was able to rest the panel on top of the washer. The rest of the washer came apart quickly just moving down the front of the washer and removing the door, latch, tub gasket, drain cover. Removing the pump was just a mater of disconnecting the drain hoses, and one clip under the drain assembly. 3 screws attach the drain to assembly to the pump and only 2 wires that are clearly marked. Reassembly is just going back through in reverse antaran of disassenbly. The best thing about this is that it all comes apart with a standard phillips screwdriver.
Read more…

Direct Drive Water Pump

PartSelect Number
PS11741239

Manufacturer Part Number
WP3363394

The direct drive drain pump (Whirlpool Direct Drive Washer Pump, Drain Pump, Washer Drain Pump, Water Pump) removes water from the washer during the drain cycle without the use of a belt. The pump is supposed to drain the water from the washer; if the water isn’horizon draining or if there is a leak, you may have a problem with your pump. You must replace this part if there is a blockage or clog. Although the symptoms may point to a malfunctioning drain pump, there could actually be a problem with one of the connecting hoses. This pump connected directly to the motor, and comes in white plastic. This replacement part features 1 direct drive water pump with 2 ports for water to pass through: a large one and a smaller one.

Read:  The Two Topics of Primary Concern in Macroeconomics Are

Fixes these symptoms

  • Fills and drains at the same time
  • Leaking
  • Leaks water
  • See more…

Installation Instructions

RICHARD from PHILA, PA

Replace Water Pump Coupling

Removed casing komisi over washer disconnected water pump. Disconnected gembong then replace coupling then reassemble motor then replaced water pump.
Read more…

Washer Drain Pump

PartSelect Number
PS11757304

Manufacturer Part Number
WPW10730972

This is a manufacturer-approved replacement drain pump for your washing machine. To complete this repair you will need a 1/4 inch nut driver, 5/16ths nut driver, a flat blade screwdriver, and a pair of pliers. Make sure to disconnect power to the washer before beginning this repair.

Fixes these symptoms

  • Burning smell
  • Engine runs but does not pump water
  • Leaking
  • See more…

Installation Instructions

Andrew from St.Louis, MO

F 21 error

Removed the front panel unplugged
The washer drained water out, lift the washer up to un screw the drain pump. Then unhooked the hoses from pump put the other pump in.

Read more…

Drain Pump Kit

PartSelect Number
PS1485610

Manufacturer Part Number
280187

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. This part is used on front load models.

Fixes these symptoms

  • Leaking
  • Noisy
  • Pumps but will not spin
  • See more…

Installation Instructions

Donald from Wichita, KS

Washer would titinada drain ,F02 and SUD code displaying

(1) First I unpluged the washer then I removed the water from the tube with a water vac.(2) Then I removed the three (3) screws that holds the front panel, using a Torx T-20 socket. ( this is a front load washer ). The panel is below the loading door.

(3) I packed towels under the washer.
(4) I slowly removed the cleanout in the front of the pump, using the water vac to catch the water as it leaked out.
(5) I removed the wiring to the motor.
(6) I removed the screw that holds the pump in place with a Torx T-20 socket.
(7) I pulled the pump forward so the clamps that hold the drain hose and discharge hose could be removed using the hose clamp pliers. ( they come off much easier then they go back on ).
(8) I tested the pump and found it would run but was making a lot of noise and running slow.
(9) To reinstall start with number (7) and work backwards to number (1) skipping (3) and (4).
Don Kramer
Wichita, Kansas

Read more…

Drain Pump – 120V 60 Hz.

PartSelect Number
PS7783938

Manufacturer Part Number
137221600

This is a 120 volt, 60 hertz drain pump that is manufactured to remove water from the tub of your washer once your clothes are washed. This part is the pump and motor assembly, which includes a red flapper to prevent drain backflow. You will need to remove the front panel of your washer to access the drain pump. The tools you will need for the repair are a Phillips screw driver, a putty knife, a pair of slip joint pliers, and a 5/16 nut driver. Be sure to disconnect the water supply from your washer before doing the repair. The metal edges on the appliance are sharp, so use work gloves to safely complete the repair.

Read:  What is a Bear Hug Finance

Fixes these symptoms

  • Leaking
  • Noisy
  • Titinada draining
  • See more…

Installation Instructions

kenneth from willard, OH

would’tepi langit spin all water out or rinse out clothes

uplugged washer took front off washer 2 screws pryed up top pump was mounted with 2 screws and 2 wires took off found change in pump and the fins to pump worn off ordered part off line the wait for part was longer than the amount of time to fix masalah and cost of part saved berpenyakitan about $25-35 if I was to buy local worth wait save money and fix problem washes like new spins and drains all water from tub.
Read more…

Drain Pump – 120V 60Hz

PartSelect Number
PS11751719

Manufacturer Part Number
WPW10276397

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time

Fixes these symptoms

  • Leaking
  • Will not drain
  • See more…

Installation Instructions

REED from BUCHANAN, NY

Wouldn’lengkung langit drain pump made loud noise

Removed old drain pump and found a sock in the inlet – must have burned out pump because after removing it pump was still defective. Installed new pump in about 30 minutes and off to the races no more issues
Read more…

Drain Pump

PartSelect Number
PS5136124

Manufacturer Part Number
W10536347

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.

Fixes these symptoms

  • Leaking
  • Noisy
  • Pumps but will not spin
  • See more…

Installation Instructions

ROBERT from BARRINGTON, IL

Loose change entered drain pump, cracked housing leaked all water out

Disconnect power, hot/cold supply and drain hose. Tip washer onto front side, expect some additional water to leak out. Remove the cracked drain pump, 3 screws, hose clamps, and electrical plug.

Tip washer back up, use the putty knife to pop the top cover up (clips are about 6.5in in from sides). Unclip the white plastic cover over the outer and inner tubs. Pop the center cap from inside the inner tub, exposing the bolt holding the inner tub down. Remove bolt, pull inner tub up and out.

At bottom of outer tub remove 2 screws from drain access cover, should find some change under there (or in the pump).

Re-assemble using new pump.

Note:
Before new pump arrived I was able to use some silicone sealant, epoxy, and black tape to temporarily fix the cracked pump housing after pulling it out.

Read:  Can I Use Fsa for Lasik


Read more…

Water-Pump

PartSelect Number
PS11738156

Manufacturer Part Number
W10876600

Drain Pump – 60Hz 120V

PartSelect Number
PS2342445

Manufacturer Part Number
137108000

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.

Fixes these symptoms

  • Leaking
  • Noisy
  • Titinada draining
  • See more…

Installation Instructions

Charles from Raleigh, NC

drain pump motor batas seized as result of foreign objects

After turning off water, disconnecting power, and sucking water out of the tub and drain hose with a shop vac, I removed the front kick panel (took out two sheet logam screws). Then I removed two mounting screws from the pump assembly, and disconnected two hose clamps (inlet and outlet hoses) with a pair of pliers. Very simple, very easy. The pain in the fanny came when I tried to reattach the hoses. The hose clamps apparently require either a special tool or a technique I’m not familiar with. I finally tossed them and purchased two standard screw and band hose clamps which made the final connections a breeze. The surprise came when I found that the penggerak takat seized because of a pair of tweezers that had somehow worked into the penggerak impeller. Free of tweezers and coins, the new motor works great! To quote another one of your contributors: wife happy!
Read more…

PUMP-WATER

PartSelect Number
PS11757016

Manufacturer Part Number
WPW10661045

Installation Instructions

John from LEXINGTON, NC

Easy to install

I just drained the washer and unscrewed the 3 screws unhooked the hose clamp and installed the new one attached the hose and hose clip. Really easy. Took longer to try up water in floor than installing.
Read more…

Related Parts